Why don't my plinth, base and cornice follow the cabinets in imos iX, and how do I fix it?
Plinths, bases and cornices are length parts. They only follow the cabinets when the article category is right, and in a corner only when a real corner unit is drawn there.
Short answer: in imos iX, plinths, bases and cornices are not part of the cabinet. They are length parts calculated across one or more cabinets, and they are only placed automatically when the cabinet has an article category. When the layout changes, from imos iX 2025 you edit the existing length part with the wrench icon; there is no longer any need to delete it and place it again. In a corner, a length part only continues automatically when a real corner unit is drawn there.
Applies to
- imos iX CAD; automatic length parts through the article category have existed since imos 12. Based on libraries we built between imos iX 2017 and imos iX 2023
- Functions: Artikel Categorie (article category), length parts (plinth, worktop, cornice, light rail), iX Elementen (iX Elements), Opdracht variabelen (order variables) and value sets, Artikel Specifieke variabelen (article-specific variables)
- Editing existing length parts with the wrench icon: from imos iX 2025. In older versions you delete the length part and place it again
- Integrations: cutting list and optimisation software (lengths and joints)
- Last reviewed: October 2026
First, what is a length part?
imos draws a plinth, worktop, cornice (also called crown moulding or top plinth) or light rail as a length part. That is a separate element calculated across the selected cabinets: one continuous plinth rather than a piece per cabinet. So it doesn't automatically follow everything you do to the cabinets afterwards.
Step 1: check the article category
This is the most common cause. Without an article category there is no automatic plinth or worktop, and manual length parts don't work either.
- Select the cabinet that isn't getting a plinth or cornice.
- Open it in the Artikel Designer (Article Designer).
- Check that a category is linked under Artikel Categorie.
- Open the category and check which length parts it contains: plinth, worktop, cornice and/or light rail.
- Check the insertion position as well. That is what puts base units at plinth height by default.
- Save the article and place the cabinet in the drawing again.
Point the length parts in the article category to a variable and give it a value set. The draughtsman then picks a front-only, front-and-left or all-round plinth in the Opdracht variabelen (order variables) with one choice.
Step 2: placing a base
- Fill in the base variable first, before placing any cabinets.
- Place the cabinet. The base is added underneath automatically.
- Check that the levelling feet follow the plinth height. In a well-built library the foot height refers to a single variable, for example
$PLINT_HOOGTE. - Then place the front plinth through the length parts.
Step 3: editing an existing plinth after a change
Moved, added or removed cabinets, or want a different plinth type? From imos iX 2025 you no longer need to delete the length part.
- Select the existing plinth length part.
- Click the wrench icon.
- Change the plinth principle, the cabinets or the overlengths.
- Confirm the change.
- Check in a view that the plinth runs through and stops correctly at the end panels.
Using a version before imos iX 2025? Delete the existing length part, select all cabinets that should share one continuous plinth and choose the plinth principle again from the length parts.
Step 4: placing a cornice
- In iX Elementen (iX Elements), click the globe icon.
- Choose the top rail (cornice) from the length parts.
- Select the cabinets the cornice should run across.
- Confirm with Enter.
Watch out with filler strips: in one library we supported, the cornice wouldn't run correctly over a filler strip beside the cabinets. In that version it couldn't be configured, and it was reported to the software vendor as a development request. The workaround that works: don't include the filler strip in the selection, give the cornice an overlength on that side equal to the strip width, and correct the other side with a negative overlength if needed.
Best practice: a length part from one cabinet with overlengths
With unusual shapes you don't have to draw a plinth or worktop across every cabinet. It often works better to place the length part under or on a single cabinet and then bring it to the right length with overlengths.
- Select one cabinet as the base, for example the cabinet in the middle of an island.
- Place the plinth or worktop on that cabinet only, through the length parts.
- Select the placed length part and click the wrench icon.
- Enter the left and right overlength until the length part reaches the end points you want.
- Enter a rear overlength if needed, for example for an overhanging worktop.
- Check the length and end points in a plan and front view.
Example from practice: an island with an end panel on the left and right and a bar construction, where the bar itself isn't drawn as an imos iX cabinet. Place the worktop or plinth from one cabinet and extend it with overlengths, and the software ignores the span of the bar construction. The length part simply ends up where you intended.
Corners: always draw a real corner unit
In a corner layout, plinths, cornices, light rails and worktops only run through correctly when a corner unit is drawn in the corner. imos recognises it as a corner unit and automatically turns the plinth and worktop around the corner.
Want a blind corner? That's fine, but draw it as a corner unit, not as a straight cabinet with a blind panel. That way the length parts stay right automatically with a blind corner too.
Two straight cabinets in a corner don't work. If you put two straight cabinets against each other with a rotation, imos doesn't see a corner unit. The plinth, cornice, light rail or worktop won't turn around the corner and you have to correct it by hand.
Use a blueprint corner unit. The Wood Intelligence database from Wood Intelligence Plus includes several corner unit principles as blueprints in its article library. One example is the LeMans corner unit, which is genuinely drawn as a corner unit: as soon as you place it, the plinth and worktop continue around the corner automatically. Use such a corner unit as the basis for your own corner solutions, blind corners included. Read more about Wood Intelligence Plus.
Exceptions: end panels, corners and joints
- End panel on the plinth or on the floor. If the end panel stops on the base, the plinth must run underneath. If the end panel stands on the floor, the plinth stops against it. Handle this with a separate article category per variant, so the plinth comes out right automatically.
- Joints. Let imos warn you when a plinth is too long, but don't let it create joints automatically. Decide where the joint goes yourself.
Why this approach?
In the workshop a cabinet and its plinth lead separate lives. The cabinet is a carcase; the plinth is one long strip running across several cabinets, with overlength at mitres and a joint where the board runs out.
The article category is the link. It defines which length parts a cabinet type gets, where the snap points are and at what height the cabinet is inserted. A cabinet without a category is invisible to the length parts. In practice almost every complaint about a plinth that doesn't come along traces back to a missing or wrong category.
Corners follow the same principle: imos reads from the article that a cabinet is a corner unit, and so knows the length parts must turn. To the software, two rotated straight cabinets are just two separate straight cabinets.
Deliberately updating a length part, with the wrench icon or by placing it again, is predictable: only moving the cabinets easily leaves a plinth that is just too short or overhangs. Fixed details, such as 10 mm overlength on mitred edges or a plinth 1.5 mm shorter at the top, belong in the plinth principle, not in manual fixes afterwards.
Common mistakes
- No article category linked. No automatic plinth, and placing length parts doesn't work.
- End panel from the wrong folder. Using a tall-unit end panel on a base unit gives a plinth that stops or runs through in the wrong place.
- Leaving the plinth after moving cabinets. Check the length part after every layout change and update it with the wrench icon (from imos iX 2025) or place it again.
- A corner built from two rotated straight cabinets. The plinth and worktop won't continue around the corner. Draw a corner unit, even for a blind corner.
- Setting the base variable too late. Fill in the base and plinth variables before placing cabinets, or feet and insertion height won't match.
Compare with an example cabinet. The Wood Intelligence database from Wood Intelligence Plus contains an example cabinet for each cabinet concept, built with variables and proven in practice. If your plinth or base doesn't follow, compare your cabinet with the example cabinet of the same concept. That quickly shows which setting or reference is missing. Read more about Wood Intelligence Plus.
Frequently asked questions
Why does my new cabinet get no plinth when the others do?
Almost always the article category is missing on that article, for example because it is a copy or a newly built cabinet. Link the category in the Article Designer, save the article and place the cabinet again.
Can I replace the automatic plinth with a different one?
Yes. Pick a different plinth type through the variable, or select the plinth and choose a different plinth principle with the wrench icon (from imos iX 2025). In older versions you delete the length part and place the plinth you want again across the selected cabinets.
Why doesn't my plinth or worktop continue around the corner?
Most likely two straight cabinets have been placed against each other with a rotation. imos only turns length parts when a real corner unit is drawn. Replace the corner with a corner unit, as a blind corner if needed, and update the plinth and worktop.
How do I place a plinth or worktop on an island with a bar construction?
Place the length part on one cabinet and bring it to the right length with left, right or rear overlengths. That way imos ignores the span of the bar, which isn't drawn as a cabinet.
How do I avoid a plinth longer than the board?
Set a maximum plinth length warning in the length parts. You get a warning and decide where the joint goes. We advise against automatic joints.
Further reading
- Variables for cabinet height, plinth and front gaps in imos iX
- Handles, handle profiles and handleless fronts (Tip-On) in imos iX
- Grain direction and rotated grain in imos iX
- Consultancy
More than one solution
Almost every question in this knowledge base has more than one solution. The best fit depends on your workflow, machinery and integrations. Not sure which applies to you, or are you using software we don't (yet) support? Feel free to email Wood Intelligence. We're happy to think along with any challenge.
imos is a trademark of imos AG. LeMans is a trademark of Kesseböhmer. Wood Intelligence is an independent consultancy.