How do I work with handles, handle profiles and handleless fronts (Tip-On) in imos iX?
Choose the cabinet concept first (handle, handle profile or Tip-On) in the variables; door principles, connector scan and length parts do the rest.
Short answer: in imos iX, always decide the cabinet concept first in the variables: cabinets with handles, handleless with a handle profile, or handleless with Tip-On. Then pick the handle and its position through value sets and Scan verbinders (connector scan), place handle profiles across several cabinets as a length part, and let Tip-On adjust the front gap and buffers automatically.
In Wood Intelligence implementations we often see that the handle is only known late. With a handle drilling in Scan verbinders and the handle concept as the first order question, drawing can carry on anyway.
Applies to
- imos iX CAD; based on library set-ups we built between imos iX 2019 and imos iX 2025
- Functions: variables and value sets, Scan verbinders (connector scan), connectors and work groups, length parts, Variabele lijst (variable list)
- Hardware: handles and knobs, aluminium and timber handle profiles, Blum Tip-On and Hettich push-to-open
- Integrations: CAM iX (milling for handle profiles), optionally imos iXPlan
- Last reviewed: November 2026
Wooden or aluminium handle profiles for handleless kitchens in imos iX
Drawing handle profiles for handleless kitchens (video in Dutch).
Step 1: choose the cabinet concept
Handles, handle profiles and Tip-On affect front gaps, drawer division, buffers and machining all at once. So you don't start with the handle; you start with the concept.
- Look at the drawing and decide whether the job uses handles, handleless with a handle profile, or handleless with Tip-On.
- Open the order variables.
- Pick the cabinet concept from the value set. Always make this the first step.
- If one cabinet differs, set the concept per article in the article-specific variables.
- Then expand the concept and answer the remaining order questions, such as profile type or handle orientation.
In a well-built library the doors are split by cabinet type, for example doors for base units, tall units, wall units and mid-height units. Per type the handle always sits in a fixed place: at the top on a base unit, at the bottom on a wall unit. The draughtsman never has to position handles door by door.
Step 2: choosing and swapping handles
- In the handle concept, choose the handle orientation, for example vertical, horizontal or horizontal centred.
- Select the cabinet.
- Choose Scan verbinders.
- Pick an existing handle from the list.
- Click Ok. With several doors, choose the handle per door.
What Kies_Greep_Concept sets in one go
In a library based on Wood Intelligence Plus, the concept question is called Kies_Greep_Concept (choose handle concept). You choose Greep (handle), Aluminium Greeplijst (aluminium handle profile), Houten greeplijst (wooden handle profile) or Tip On. You must always make this choice, even when the default seems right.
Each choice is backed by a value set. It sets four underlying groups at once:
| Value set | Kies_Artikel_Greep_Type | Kies_Element_Type | Kies_Front_Voegen | Kies_Greeplijst_Type |
|---|---|---|---|---|
| Greep (handle) | Greep, Horizontaal | Grepen | Standaard | Niet_Greeploos |
| Tip On | TipOn Staanders (Adapter) | Grepen | Standaard | Niet_Greeploos |
| Greeploos Aluminium (handleless aluminium) | Greeploos | Greeploos Aluminium | Greeploos | Aluminium profile, recess in sides only |
| Greeploos Hout (handleless wood) | Greeploos | Greeploos | Greeploos | Wooden profile, recess in sides only |
So one click controls, among other things:
- whether the sides get handle recesses;
- whether the fronts get handles;
- whether the sides get Tip-On pins;
- the front gaps that connect the fronts to the uprights.
Need your own variant? Add a new set under Waarde sets (value sets) in the Kies_Greep_Concept group and fill in the four groups. Switching stays a single click, even for a concept only your company uses.
Put the handle's order number or a free comment in the connector. That information then also appears on the assembly list, so nobody has to look up what to order for special handles.
Creating a new handle
The quickest way to a new handle is to copy an existing one that resembles it as closely as possible. A 128 mm handle is a good starting point for another 128 mm handle; a rectangular routed grip for a new rectangular routed grip.
- Select the cabinet.
- Choose Scan verbinders.
- Select the handle closest to the new one, with the correct hole spacing.
- Click the red browse button to go to the database.
- Give the copy a new name.
- Open the linked connector and give it a new name as well.
- Adjust the connector's work group: check the spacing for drillings, or length, width and depth for pocket milling.
- Link the DWG with the handle's 3D model. Suppliers can often provide one.
- Click Toepassen (Apply) and save the connector set.
- Refresh the cabinet, select the new handle in Scan verbinders and check that the 3D model is rotated correctly.
Drawing handle profiles
For a handleless concept with profiles, the variables usually ask for:
- Profile type: aluminium or timber.
- Profile location: C and L profile (default), L only or C only.
After this choice imos only creates the recesses in the sides where the profile runs. You place the profile itself as a length part:
- Select all cabinets that share one continuous profile.
- Pick the handle profile from the length parts.
- Check in a view that the profile runs across all cabinets.
If you want a profile per cabinet instead, for example for visualisation in imos iXPlan, set up a separate variant for that.
Vertical handle profiles on tall units
- In the handle variables, choose vertical handle profiles (tall units only).
- When inserting the tall unit, use the Variabele lijst (variable list) to set the setback for the profile straight away, usually on the non-hinge side only.
- Switch to plan view.
- At the setback, place the vertical profile principle you need, for example a C profile between two cabinets.
- Check in plan view that the profile snapped to the correct cabinet.
Handle rotation: all handles horizontal or vertical
- Set Kies_Greep_Concept to Greep.
- Expand the group and open Kies_Artikel_Greep_Type.
- Choose Greep, Horizontaal, Greep, Horizontaal (Midden gecentreerd) (centred) or Greep, Verticaal.
- Refresh the cabinets. All handles rotate at once.
Handle reference: front face or inside of the front
By default the handle sits on the front face. Some profile handles are screwed to the back of the front instead. In that case choose a (Binnenzijde) (inside) variant in Kies_Artikel_Greep_Type, such as Greep, Horizontaal (Binnenzijde) or Greep, Verticaal (Binnenzijde). The drillings and the 3D model then move to the inside of the front.
Handle not chosen yet? Use a handle drilling
The handle is often still unknown while drawing. You would rather avoid that, but a handle drilling lets the draughtsperson carry on.
- Select the cabinet.
- Choose Scan verbinders (scan connectors).
- On the left, click the door's handle, for example Greep deur onder (handle lower door).
- On the right, choose a final handle or a drilling at centre distance, such as Greepboring_032mm or Greepboring_064mm.
- Click OK. Once the handle is known, switch to the real handle the same way.
Watch out with drawers: in a handleless concept the profile height is always deducted at the top and the bottom, which makes low drawers harder to fit. Link the drawer front division to a variable or formula so the fronts stay equal. A real-world example: 1:1:1 divides on centre lines; 1-15mm:1:1:1-15mm corrects for equal fronts.
Handleless with Tip-On
If you choose Tip-On at concept level, a well-built library adjusts automatically:
- The fronts sit 3 mm from the carcase, giving the Tip-On unit enough push travel.
- Drawers get a Tip-On runner instead of a standard runner.
- Handles are switched off.
- Door buffers are dropped; they only appear on doors without Tip-On.
You link the Tip-On unit and its adapter to the hinge set. Its position is set per door type, on the side panel or on the top or bottom panel. For vertical placement we use a division: 1:50mm for a lower door, 50mm:1 for an upper door and 1:1 for a middle door. For horizontal placement, keep the connector's default values.
Tip-On position per door type
You choose where the Tip-On or push-to-open pin goes in Kies_Artikel_Greep_Type:
- At main level, choose the default, usually TipOn Staanders (Adapter) (on the uprights, with adapter).
- Expand Kies_Artikel_Greep_Type. Below it, each door type has its own group, such as DRA_Greep_Algemeen, DRB_Greep_Onderin, DRM_Greep_Midden and DRO_Greep_Bovenin, plus KPB_Greep_Midden and KPO_Greep_Midden for flaps.
- Only choose another position where it differs. Example: the lower door gets its pin on the top panel, so TipOn Dek (Adapter).
What do TOS, TODA and TOBA mean?
Working with imos means working with abbreviations. The hinge sets have been extended with the Tip-On variants:
| Abbreviation | Meaning |
|---|---|
| TO | Tip-On |
| TOS | Tip-On on the upright |
| TOSA | Tip-On on the upright with adapter (holder) |
| TOD | Tip-On on the top panel, screwed directly |
| TODA | Tip-On on the top panel with adapter |
| TOB | Tip-On on the bottom panel |
| TOBA | Tip-On on the bottom panel with adapter |
Because the pin is linked to the hinge, every pin position gives its own hinge principle. That lets you choose the pin position per door without changing the hinge itself.
Choosing the colour of the Tip-On pin
- Open Kies_Materialen and then Kies_Kleur_Mapping (colour mapping).
- Open the mapping of the push-to-open system, for example Kleur_Push_To_Open_Hettich.
- Choose the colour, for example WIT (white) or ANTRACIET (anthracite). All types (TOBA, TODA, TOSA) follow that choice.
Watch out with Tip-On: because the front moves forward, the carcase size you enter in the Article Designer does not change. You have to check the total depth of carcase plus front yourself. If you mix cabinets with handles and Tip-On cabinets, set everything to Tip-On and then give the handle cabinets a handle. That keeps all fronts in one line.
Why this approach?
Choosing a handle is never just choosing a handle. It drives front gaps, the distance between front and carcase, drawer division, buffers and CNC machining. By steering all of that through one concept choice, you switch between handle, profile and Tip-On with a single click instead of revisiting every cabinet.
We draw handle profiles as length parts, not per cabinet, because the workshop wants one long profile across several cabinets, not loose pieces. For CAM, profile recesses use a profile that clips the machining at the panel edge and left- and right-hand tools, so the edge banding doesn't tear off. A separate component is less attractive here: with panel rotations you can't always predict where the profile will end up.
We create new handles by copying rather than from scratch. Hole spacing, work groups and the link to the 3D model stay correct, and the library stays tidy.
Common mistakes
- Choosing handles before the concept. Placing handles first and switching to handleless later risks wrong gaps or redundant drillings.
- Mixed upper and lower case in value sets. We have seen existing sets stop working because the spelling didn't match. Keep names exactly identical.
- Trusting the buffer proposal blindly. The automatic door buffer proposal is right in roughly 90 to 95 percent of cases. Manual overhangs larger than the search radius break it, so check.
- Snapping to the wrong cabinet with vertical profiles. The profile easily jumps to the neighbouring cabinet. Place it from plan view.
- Forgetting depth with Tip-On. The front moves forward; the carcase size doesn't.
Handle concepts ready to use. In the Wood Intelligence database from Wood Intelligence Plus, the handle concepts are fully worked out and variable: handle profiles for handleless cabinets, vertical or horizontal handles, handles behind the door, profile handles on the door and TIP-ON, where the right TIP-ON type is selected and positioned automatically. With one click you switch a handleless cabinet to a cabinet with handles and back. Front sizes and the alignment of the lines across a kitchen are set correctly automatically. Read more about Wood Intelligence Plus.
Frequently asked questions
Can I combine handle cabinets and Tip-On cabinets in one order?
Yes. Set the whole order to Tip-On, then give the cabinets that need a handle a handle. All fronts then keep the same distance to the carcase and line up.
Why do I only see recesses and no handle profile?
That is by design. The concept creates the recesses in the sides; you place the profile itself as a length part across the selected cabinets. You get one continuous profile instead of a piece per cabinet.
Why do the door buffers disappear when I choose Tip-On?
Door buffers are linked to the hinges and only appear on doors without Tip-On. With Tip-On the push unit takes over the buffer's role, and a buffer would get in the way of opening.
Do I need to build a new handle for every size?
Only if the handle isn't in your library yet. Then copy an existing handle with the same hole spacing or milling principle, rename both handle and connector, and change only the work group and the DWG.
What do TOS, TOSA, TOD, TODA, TOB and TOBA mean in imos?
They are the positions of the Tip-On or push-to-open pin: S = upright, D = top panel (dek), B = bottom panel. A trailing A means with adapter (holder). TODA is Tip-On on the top panel with adapter.
The handle has not been chosen yet. Can I keep drawing?
Yes. In Scan verbinders, choose a handle drilling at centre distance, such as Greepboring_032mm. Once the handle is known, switch to the final handle in the same place.
How do I make all handles vertical at once?
Set Kies_Artikel_Greep_Type to Greep, Verticaal and refresh the cabinets. Choose the (Binnenzijde) variant for profile handles screwed to the back of the front.
Further reading
- Machining principles and formatting classes in CAM iX
- Naming materials and edge banding in imos iX
- Placing and renumbering position numbers in imos iX
- Consultancy
More than one solution
Almost every question in this knowledge base has more than one solution. The best fit depends on your workflow, machinery and integrations. Not sure which applies to you, or are you using software we don't (yet) support? Feel free to email Wood Intelligence. We're happy to think along with any challenge.
imos is a trademark of imos AG. Blum and TIP-ON are trademarks of Julius Blum GmbH. Hettich is a trademark of Hettich Holding GmbH & Co. oHG. Wood Intelligence is an independent consultancy.