How do I place drawers, cutlery drawers, a clothes lift and lift systems in imos iX?
Choose drawers through variables or the connector scan, build a cutlery drawer with virtual zones, turn a door into a flap and order drawers via CSV.
Short answer: in imos iX a drawer is a connector inside a zone. You choose the drawer system through variables or through Scan verbinders (connector scan), and imos only offers drawers that fit the zone. A cutlery drawer behind a tall drawer front is drawn with a virtual zone division, a VF drawer and an inner drawer. A lift system is created by turning a door into a flap; a clothes lift goes into the Artikel Designer as a sub-article.
Applies to
- imos iX CAD; based on library set-ups from imos iX 2019 up to recent versions.
- Functions: Scan verbinders (connector scan), Artikel Designer (zones, divisions, sub-articles), article-specific variables and value sets
- Hardware: Blum LEGRABOX, MOVENTO and MERIVOBOX, AVENTOS HK top and HK-S, clothes lift
- Integrations: CSV export for drawer orders, hardware list and ERP
- Last reviewed: October 2026
Choosing a drawer
- Select the cabinet and open the article-specific variables.
- Pick the drawer system from the value set: LEGRABOX, MOVENTO or MERIVOBOX.
- Pick the drawer colour.
- Pick the runner: Blumotion or Tip-On Blumotion.
- Click Toepassen (Apply).
- For a different drawer, select the cabinet and open Scan verbinders. Only drawers that fit the zone height are listed.
Drawer variables per position. In a variable cabinet, each drawer position has its own variable, for example $Type_Lade for a drawer with front, $Type_Binnenlade for an inner drawer and $Type_Lade_VF for a drawer behind a separate front. Give every drawer cabinet these variables in the Artikel Designer.
Two drawers with a cutlery drawer behind
- Draw a virtual zone division in the cabinet.
- Place a VF drawer (separate front) in the lower zone. It creates the machining in the front.
- Place an inner drawer in the upper zone: this becomes the cutlery drawer.
- Set the fixed front to the full height.
- Choose the drawers you want through Scan verbinders.
- If the system you want doesn't fit, change the height of the virtual zone. Other drawer heights then become available.
Filler pieces for LEGRABOX
25 mm plastic filler pieces sit between the cabinet side and the drawer runner. They give the drawer extra side clearance, for example for an inner drawer. You choose left, right, both or none, and the filler colour.
In the Wood Intelligence database the filler pieces are now linked to the LEGRABOX connector sets. Place the drawer and the fillers come along automatically. If your library doesn't have that link, you draw them yourself:
- Create a virtual height division at shelf level, not 1:1:1 per drawer.
- Create a width division in each zone:
25mm:1,1:25mmor25mm:1:25mm. The 25 mm part is the filler. - Place the drawer in the middle part.
Check the filler position. We have seen inner drawers where the filler ended up outside the cabinet while the drilling still has to go into the side panel. Check this after placing.
Placing a lift system
- Select the door and turn it into an upward-opening flap. An upward flap is linked to AVENTOS HK.
- Choose the lift system type through the variable, for example HK top or HK-S, with Blumotion or Tip-On Blumotion.
- Choose the cover cap colour.
- Open Scan verbinders and check that a lift system has been selected.
- If it shows Geen selectie (no selection), hover over that line. You will see the values imos is searching with.
- Compare them with the range Blum specifies and adjust the front size if needed.
imos calculates the power factor from front height and weight, including any handle, so the front material needs a weight.
Flap not fully overlaid? The lift system measures from the top of the front, not from the inside of the cabinet. For a half-overlay flap, add the top panel thickness and top front gap through a variable.
A clothes lift in a wardrobe
- Open the wardrobe in the Artikel Designer.
- Choose the zone where the lift goes.
- Place the clothes lift as a sub-article in that zone.
- Place the cabinet back in the drawing and check the lift in 3D.
Ordering drawers automatically via CSV
For each order a CSV export creates a drawer order report: one line per cabinet position and drawer version, with drawer type, operation, runner (40 or 70 kg), height, length, width, colour, any anti-slip mat and quantity. Fronts are left out.
- Save the order.
- Run the drawer export for the order, the same way as a cutting list export.
- Check positions and quantities in the CSV file.
- Send the file to your hardware supplier or import it into your ERP.
Why this approach?
Because a drawer is a connector, imos filters on height and depth itself; you can't pick a drawer that doesn't fit. With drawer variables per position you switch a whole project to another system without redrawing. Filler pieces inside the connector set save the manual width division per zone, which took a lot of time.
The CSV export reads drawer type, height, length and colour from the connector name. Consistent naming is therefore the foundation of automatic ordering. In practice it saves retyping and wrongly ordered drawers.
Common mistakes
- Zone too low or too shallow. Scan verbinders then shows few or no drawers.
- Front material without weight. The power factor is wrong and imos picks the wrong lift system, or none at all.
- Inconsistent connector names. The CSV export can't recognise type or height and writes
Onbekend(unknown) in the column.
Working with Wood Intelligence Plus? The Wood Intelligence database contains Blum LEGRABOX, MOVENTO and MERIVOBOX and the AVENTOS HK top lift system, in all colours and variants, with the filler pieces already linked to the LEGRABOX connector sets. Read more about Wood Intelligence Plus.
Frequently asked questions
Why do I only see a few drawers in the connector scan?
imos only shows drawers that fit the zone height. Change the zone height, for example in the virtual division, to make other drawer heights available.
Can I choose Tip-On or Blumotion per drawer?
Yes. You choose the runner type through the variable: Blumotion or Tip-On Blumotion. In a Tip-On cabinet concept the library usually sets the runner to Tip-On automatically.
Do I have to build the drawer order report myself?
The report is an SQL view on the order's connectors plus an export configuration that only picks up LEGRABOX connectors. You set it up once per database, matched to the columns your supplier asks for.
Further reading
- Collision check for hinges, drawers and fronts in imos iX
- Creating new handles, locks or hardware in the imos iX database
- Connecting imos iX to your ERP with one article code
- imos training
More than one solution
Almost every question in this knowledge base has more than one solution. The best fit depends on your workflow, machinery and integrations. Not sure which applies to you, or are you using software we don't (yet) support? Feel free to email Wood Intelligence. We're happy to think along with any challenge.
imos is a trademark of imos AG. Blum, LEGRABOX, MOVENTO, MERIVOBOX, AVENTOS, TIP-ON and BLUMOTION are trademarks of Julius Blum GmbH. Wood Intelligence is an independent consultancy.