How do I use the collision check in imos iX for hinges, drawers and fronts?
The collision check makes imos iX warn you when a hinge hits a shelf or another panel. Here is how to switch it on and resolve a collision.
Short answer: the collision check in imos iX warns you as soon as a connector, in practice usually a hinge, hits a shelf or another panel. You switch it on with the line COLLISION_CHECK_CONNECTORS=2 in imos.ini and draw a bounding box (kaderbox) in the connector. imos reports the collision but does not fix it: the designer decides how.
Applies to
- imos iX CAD; based on libraries we set up between imos iX 2019 and imos iX 2025
- Functions: the imos.ini setting
COLLISION_CHECK_CONNECTORS, bounding boxes in connectors, Toon panelen (show panels) - Hardware: hinges, for example overlay and inset
- Last reviewed: October 2026
Step 1: switch on the collision check
- Close imos and make a copy of imos.ini. To find that file, see Where is imos.ini and what can I change?
- Find the line
COLLISION_CHECK_CONNECTORS. If it is missing, add it with the other imos settings. - Set the value to
2. With0the check is off. - Save and restart imos.
Step 2: draw the bounding box and resolve the collision
- Open the hinge connector.
- Draw a bounding box: a virtual box around the hinge. Anything in the cabinet that falls inside it counts as a collision. Measure from the centre point of the hinge.
- Repeat this for every hinge type you use.
- Place a cabinet with shelves and a door. If a hinge collides, a message appears after placing the article.
- Choose Toon panelen (show panels). The colliding elements are shown in blue.
- Move the hinge using the hinge variable (see below) or move the shelf.
Recommended: move the hinge using the variable
In the Wood Intelligence Plus library we made sure you can move a colliding hinge simply by entering a value in the hinge offset variable. Count from the bottom and enter 100 (100 mm up) or -100 (100 mm down) for the colliding hinge. All spacing rules keep working exactly as intended.
You can also select the hinge itself and choose Move in the iXplorer (the imos settings menu). We advise against this: it is a modification of the cabinet. With the variable, the linear spacing always stays intact. Even if you resize the cabinet later, the offset keeps working through the spacing and you can always change it again. That is why we prefer this method over the alternatives.
Why this approach?
Otherwise a colliding hinge is only discovered during installation. A bounding box defines the check once in the library. We deliberately leave the fix to the designer: sometimes moving a shelf is better.
Common mistakes
- Setting it on one workstation only. Every user needs the line in their own imos.ini.
- Forgetting a hinge type. A hinge without a bounding box is not checked.
- Moving all hinges. Move only the colliding hinge, so the rest of the spacing stays intact.
Frequently asked questions
Why is there no message even though the hinge clearly collides?
Check that COLLISION_CHECK_CONNECTORS=2 is in the imos.ini of that workstation and that imos was restarted afterwards. Then check that the hinge in use has a bounding box.
Does the collision check also work for drawers and fronts?
The check is based on the bounding box in a connector. Drawer panels or fronts that fall inside a hinge's box are therefore reported. If you want a drawer system or lift system to be checked as well, that connector needs its own bounding box. In practice we mainly set up the collision check for hinges.
Further reading
- Where is imos.ini and what can I change?
- Creating handles, locks and hardware in imos iX
- Placing drawers and lift systems in imos iX
More than one solution
Almost every question in this knowledge base has more than one solution. The best fit depends on your workflow, machinery and integrations. Not sure which applies to you, or are you using software we don't (yet) support? Feel free to email Wood Intelligence. We're happy to think along with any challenge.
imos is a trademark of imos AG. Wood Intelligence is an independent consultancy.