Skip to content
Knowledge base

How do I choose a panel's build-up and edges?

Choose the build-up of each panel with one click; the edges follow automatically and you see per edge why it does or does not get banding.

Short answer: In the cabinet editor you choose the build-up of each panel with one click, for top and bottom for example Between the sides, Over the sides or Mitre. The edges follow the build-up automatically: under Edges you see for each edge whether it gets banding and why. You can always change an edge yourself; with Back to default the panel follows the build-up again.

Information

Applies to

  • The cabinet editor of Wood Intelligence Plus (Cabinets → open a cabinet → Zones tab)
  • All parts with a build-up: top, bottom, sides, back, fronts, drawers and dividers
  • The default rules per company and per category in Construction → Panel rules
  • Last checked: November 2026

Step 1: choose the build-up

  1. Open the cabinet and go to the Zones tab.
  2. Click the panel in the zone tree, for example the top. The inspector opens on the right.
  3. In the Build-up tile, pick the card that fits: Between the sides (the top sits between the sides), Over the sides (the top rests on the sides) or Mitre (top and sides meet at 45°).

The cabinet is recalculated straight away. Joints, oversize, connections and edges take the values of the chosen build-up. For other parts, such as the back, you choose the build-up with buttons (for example Between or Overlay).

Choosing the build-up of the top with one click.

Step 2: check the edges

  1. Expand the Edges group in the inspector.
  2. The drawing shows the banding per edge: dark runs through the corner, light stops in the corner. A dotted line is an edge without banding.
  3. Below each edge you see why: Banding from the build-up, Own choice, or an edge that followed a changed joint.

For a mitred edge you also see your company setting, such as the cutting oversize, with a Change link to Panel types.

For each edge you see whether it gets banding and why.

Step 3: change an edge yourself

  1. Tick or untick an edge under Edges. That edge gets the reason Own choice.
  2. The button next to that edge resets only that edge; All edges back to default resets all of them.
  3. If you change a joint in the Joint group, the edges follow according to your company's panel rules. The Build-up tile then says Differs from this build-up with a Back to default button.
Changing an edge yourself becomes an own choice, with a button to go back.

Step 4: set the default for all cabinets

  1. Go to Construction → Panel rules.
  2. Under Applies to, choose the whole company or one category, and click Own rules if needed.
  3. Set the edges, joint, oversize and connection per edge for each build-up, and switch on Default for one build-up.
  4. Save. Beforehand you see how many cabinets the change affects; those cabinets are recalculated afterwards. Locked orders do not change.
In Panel rules you set the default per build-up.

Why this way?

Previously you chose a construction panel and a panel definition for each panel, and every banding pattern got its own panel definition (such as PD_DK_2000 and PD_DK_2200). At Wood Intelligence we saw that list grow quickly, making it hard to pick the right one. With build-ups you choose what you would say in the workshop (the top rests on the sides) and the system works out the edges and joints. The imos codes still exist, but you only see them under Advanced settings.

Tip

Want to see the imos names, create your own contour or composition, or check the rotation on the machine? See What can I do with a panel's advanced settings?

Frequently asked questions

Why is there no banding on the end of my top?

Check the reason under Edges. With Between the sides the end sits against the side and gets no banding according to the build-up. Tick the edge if you still want banding; that becomes an own choice.

How do I reset a panel to the default?

Click Back to default in the Build-up tile for joint, oversize and connection, or All edges back to default under Edges.

Can a category have a different default from the company?

Yes. In Construction → Panel rules, choose the category under Applies to and create own rules. Follow the company again removes them.

Where did the construction panels go?

They are now called build-ups and you manage them in Construction → Panel rules. The imos name of each build-up is shown on that page and under Advanced settings in the inspector.

Further reading

More than one solution

Almost every question in this knowledge base has more than one solution. The best fit depends on your workflow, machinery and integrations. Not sure which applies to you, or are you using software we don't (yet) support? Feel free to email Wood Intelligence. We're happy to think along with any challenge.

imos is a trademark of imos AG. Wood Intelligence is an independent consultancy.

Download access

Sign in to check whether this download is available.