How do I create automatic views and sections in imos iX and keep them up to date?
Plan, elevation and sections straight from the 3D model, linked to your layouts and updated with a single refresh after every change.
Short answer: save the order, then use the Views and Layout tab to create a plan view of the selected cabinets first and an elevation second. imos generates the views from the 3D model and links them to the layouts in your drawing template. After a change, refresh the views instead of creating them again.
Applies to
- imos iX CAD. This workflow has been used in practice with imos iX 2019 and later. The tab name varies by version and language; in Dutch interfaces you will see Aanzicht en Layout or Aanzichten en Lay-out.
- Modules: imos iX CAD, Visu manager, Document Manager
- Last reviewed: October 2026
Faster automatic views in imos iX
How to generate automatic views faster (video in Dutch).
Generating views
- Save the order.
- Set the Visu manager to the level you use for views (see the tip below).
- Open the Views and Layout tab.
- Choose the plan view (Bovenaanzicht in Dutch).
- Select all cabinets and, if you use one, the room.
- Then choose the elevation (Aanzicht) and select the cabinets for the front view.
- Repeat for every wall or run that needs a drawing.
Placing views in the layout
- Open the layout tab (at the bottom of the screen) that belongs to your template.
- Double-click inside the viewport to activate it.
- Zoom with the scroll wheel until the view fits the viewport.
- Double-click outside the viewport to deactivate it.
- Repeat for every viewport on the sheet.
- Refresh the title block with Refresh data block (Gegevensblok verversen) before printing.
Create a fixed level for views in the Visu manager, leaving out line boring, dowels and other clutter. Draw at a lower visualisation level and only switch higher when you need to check details. It keeps the drawing fast.
Keeping views up to date
- Change the 3D model, for example a cabinet size or a front.
- Select the view that needs updating.
- Use the refresh function for the view.
- In the refresh settings, add or remove articles if needed.
- Set the level of detail there as well: connectors, hatching and visu level.
- Then check the dimensions and view annotations.
Creating sections
- Draw the section arrow in the elevation or plan view.
- Draw the arrow from left to right.
- Check that the section is not shown mirrored.
The order in which you draw the section arrow sets the viewing direction. Draw it from right to left and you get a mirrored section.
Generating production documents automatically
- Save the drawing.
- Choose the Output tab (Uitgave).
- Choose Document Manager.
- Select the report you need, for example an exploded view per cabinet or a dimensioned drawing per panel.
- Click Apply and select the articles if prompted.
- You will find the PDF and DWG files in the order's
DOCsubfolder.
Need an installation drawing? Place installation objects (sockets, pipework) in the room and create a new view in which you select everything except the cabinets. In the conditions of your normal views, make sure installation objects and bought-in parts are left out.
Why this approach?
A view generated from the 3D model always matches what goes into production. A separate 2D drawing falls behind after the first change. That is why we refresh views rather than recreate them: the link to the layout, the scale and any manual additions are kept.
We start with the plan view because it fixes the arrangement. The elevation and sections build on it. A separate visu level for views saves a lot of clean-up. More detail in views also makes generating them slower. We often see companies show only the connectors the shop floor really needs, such as hinges.
Common mistakes
- Order not saved. Always save first. Views and Document Manager reports work from the saved order.
- Recreating views after every change. You lose viewport settings and manual dimensions. Refresh instead.
- Visu level too high. Line boring and small connectors make the view cluttered and slow.
- Expecting the Visu manager to hide everything. In some versions, connector settings from the Visu manager are not applied to views, for example levelling feet. Switch them off in the connector itself.
- Unexplained drawing errors. If views are sometimes wrong and you cannot reproduce it, have the graphics settings (
GRAPHIC.ini) checked.
Frequently asked questions
How do I remove an article from an existing view?
Use the settings that come with refreshing the view. There you can add or remove articles and change the level of detail without recreating the view.
Why is my section mirrored?
The viewing direction follows the direction in which you draw the section arrow. Draw the arrow again, from left to right.
Can I show position numbers, front heights or grain direction in the view automatically?
Yes, with view annotations (Aanzicht beschrijvingen). Based on conditions, imos places text and symbols such as position numbers, front heights, drawer types or grain symbols. Choose the annotation set, click Apply and select the view. Hinge markings only appear if connectors are visible in the view.
Can I change the wall hatching in sections?
Yes. The SECTION_WALL_HATCH_STYLE setting points to your own .pat file, and imos then uses that hatch in vertical sections.
Further reading
- Semi-automatic dimensioning in imos iX
- Setting up a drawing template and title block in imos iX
- Placing and renumbering position numbers in imos iX
- imos training
Want to learn imos iX CAD at your own pace? Wood Intelligence Plus includes a Dutch-language e-learning course for iX CAD.
More than one solution
Almost every question in this knowledge base has more than one solution. The best fit depends on your workflow, machinery and integrations. Not sure which applies to you, or are you using software we don't (yet) support? Feel free to email Wood Intelligence. We're happy to think along with any challenge.
imos is a trademark of imos AG. Wood Intelligence is an independent consultancy.